Sacramento California Winter Prep Service For Your Auto
Posted February 14, 2012 11:20 AM
When winter approaches in Sacramento California, we break out the sweaters, coats, boots and mittens. We want to be ready for winter conditions. Your vehicle needs to be ready for winter as well. The last thing you want is to get stranded out in the cold. You need your vehicle to be safe and reliable. It's a good idea to get caught up on any neglected maintenance items anytime - but the stakes are higher in the winter.
There are some specific things that we need to do in Sacramento California to have our vehicle ready for winter. The most obvious is having the antifreeze checked. If the antifreeze level is too low, it can't properly protect your engine, radiator and hoses from freezing. If your car does not seem to be making enough heat to keep you warm, your antifreeze level may be low or you could have a thermostat problem. Get it checked out. If you are due for a cooling system service, now is a perfect time to have it done.
In the cold months around Sacramento we always worry about being able to stop in time when it's slick out. The first thing to remember is to slow down and allow yourself plenty of room to stop. Of course, you want your brakes to be working properly. A thorough brake inspection will reveal if the pads or any other parts need replacing. Check with your service consultant to see if it is time to replace your brake fluid. It accumulates water over time which really messes with your stopping power.
It is a really good idea to have your battery tested. A battery's cranking power really drops with the temperature. If your battery is weak in the fall, it may not be up to winter. There is nothing like a dead battery in a snow storm.
Which leads us to an emergency kit. You should always have a blanket or something to keep you and your passengers warm if you get stranded. If you will be venturing away from civilization, pack more items such as food and water to help you survive. Keeping at least half a tank of gas is a good precaution if you get stuck and need to run the car to keep warm and it will help keep your gas lines from freezing up.
Winter in Sacramento California always makes us think of our windshield wiper blades - usually during that first storm when they aren't working right. That's why it's a really good idea to replace your blades in the fall before the winter storms. If you live where there's a lot of snow and ice, you might want a special winter blade that resists freezing up. And be sure to have enough windshield washer fluid.
The final thing to consider is your tires. Any tire can lose pressure over time - up to one pound every six or eight weeks. For every 10 degrees the temperature drops you lose another pound of pressure. So if it was 80 degrees outside when you checked your tire pressure two months ago and now it's 40 degrees out, you could be down 5 pounds of pressure. That's enough to be a real safety issue and it wastes gas too. You may need special winter tires as well. Your tire professional can help you find the right tire design for your expected road conditions.
If you're getting winter tires, it is always best to put them on all four wheels. If you are only getting two, have them put on the rear - even if you have a front-wheel drive or four-wheel drive vehicle.
This is a very important safety measure recommended by tire manufacturers. Sliding or fish-tailing on ice and snow is a matter of not having enough traction at the rear end. That is why your newest tires should always be on the rear.
Posted in the Tires and Wheels category
What Sacramento Automotive Service Consumers Should Know
Posted February 9, 2012 10:46 AM
There are some things Sacramento consumers should know about Sacramento automotive service and repair. First and foremost, Made In America / Made In Japan cares about you and your family’s safety. And we really appreciate your business. Made In America / Made In Japan in Sacramento wants to build a trusting relationship that becomes the foundation for a mutually beneficial experience for years to come.
Building on that foundation, there are some things that would help you understand the auto service and repair business better. First, it can be really hard to fix cars. The days of shade tree mechanics are long gone. The majority of automotive systems are computerized. It takes a lot of training and very expensive equipment to diagnose and repair modern vehicles. The technicians that work for Made In America / Made In Japan need extensive computer training – not just how to run the diagnostic systems, but also searching for the right parts, networking with other technicians to help them with a difficult problem and pulling together a job order that makes sure that each step of the process is addressed.
The threshold for getting started as a technician gets higher all the time and there is a huge commitment to on-going training every year. This training takes time and money. It contributes to business overhead. The average Natomas or Folsom driver may not realize the business and environmental regulations Made In America / Made In Japan must comply with. Of course that costs money too. Like any business, overhead is a big factor.
When you go into a Sacramento restaurant you don’t value the meal by what the food would cost at the grocery store. The restaurant has rent, wages, insurance, taxes, utilities, professional fees, equipment, supplies – you get the picture. The restaurant has to charge enough to not only pay for the ingredients, but for all these other things as well while making enough profit to remain in business. If you value the meal and are satisfied with your dining experience, you’ll come back and tell your friends.
It’s the same for Made In America / Made In Japan. The value of its service is not the cost of the parts they replace, but in your satisfaction with the results. If they deliver a good product at a fair price, Sacramento customers are happy to see them succeed as a California automotive business.
Contact Made In America / Made In Japan to learn more about our extensive auto service training. You can find us at: 1200 I St Sacramento, California 95814 Or call us at 916-442-3287
Your Sacramento service center loves to see its customers whenever they come in, but they would much rather see them three or four times a year for routine maintenance than once a year on a tow truck. They want to work together with you to avoid breakdowns. Tell your Sacramento area friends and family to go in for their scheduled maintenance too. That lowers the service center’s marketing costs and helps keep its labor rates down. That’s good for everyone.
Made In America / Made In Japan appreciates this great review of automotive service from AutoNetTV.
Posted in the Service Standards category
Alternative Fuel Vehicles In Sacramento California
Posted February 3, 2012 10:39 AM
Let's talk about alternative fuel vehicles. In their quest to reduce the use of fossil fuels and harmful exhaust emissions to our Sacramento environment, automakers will have a number of alternatives for us very soon.
For instance, Flex Fuel vehicles are already available in the Sacramento area. Flex Fuel vehicles can run on gasoline or on E85 fuel. E85 is a mixture of 85 percent ethanol and 15 percent gasoline. The ethanol is made from corn.
The benefits are in using less petroleum and reduced pollution. The drawbacks are that E85 gets lower fuel economy and that when gas prices are low, E85 can be more expensive than straight gasoline.
You should only use E85 if you have a Flex Fuel compatible engine. Flex Fuel vehicles have special seals and gaskets that can stand up to the high alcohol content of E85. Using E85 in a regular engine can lead to gas leaks and fires.
Diesel engines have been around the Sacramento area for a long, long time. Modern diesels are very refined and fuel efficient. Diesel fuel can be made from renewable sources like vegetable oil, too. Diesel fuel from algae and sunlight is reported to be pretty close to being commercially viable.
There are also a number of natural gas vehicles on our Sacramento roads. Gasoline engines are adapted to run on compressed natural gas. It's less expensive than gasoline and burns very cleanly. You can even refill it with a special pump from your gas line at home.
Natural gas engines don't make as much power and don't get as good of mileage, but they cost less per mile to run. The big inconvenience is that the tank that holds the compressed natural gas takes up a lot of room; even your whole trunk! And there may not be places to refuel on a road trip from Sacramento.
Plug-in electric vehicles are now available in our Sacramento area. Battery technology is the limiting factor right now. Electric cars have a limited range and are really best for use close to home. As battery technology advances, electric cars will perform closer and closer to conventional power plants.
That brings us to hybrids. There are a bunch of hybrids on our Sacramento roads, with more to come. Hybrid technology combines internal combustion engines with electric motors.
A mild hybrid has a regular gas or diesel engine that's assisted by the electric motor. The electric motor can propel the vehicle by itself up to a certain speed under gentle acceleration. There are mild hybrids in full-sized pickups and SUVs. They deliver city fuel economy similar to their highway ratings.
A full hybrid will rely primarily on the electric motor for power. It'll have a small gas or diesel engine that generates electricity for the batteries.
Another breakthrough technology is hydrogen fuel cells. Fuel cell vehicles use hydrogen to generate electricity. Several global car makers have prototypes on the road. The appeal is that the only thing that comes out of the tail pipe is water vapor. It'll take some time to build a national infrastructure of hydrogen fueling stations before there's widespread use.
A quick word about safety around hybrid and electric vehicles. Unlike the battery in your current family car, these carry enough voltage to kill you. Never mess around under the hood or with the batteries or electrical wiring. Your Sacramento service technician at Made In America / Made In Japan is trained to safely disable the flow of electricity before performing maintenance or repairs on the vehicle.
Hybrids are really not do-it-yourself vehicles unless you're specifically trained on hybrid systems.
Posted in the Fuel System category
Sacramento Safety Systems: Tire Pressure Monitoring System
Posted January 24, 2012 11:34 AM
Flats, blow outs, skids and longer stopping distances can all be the result of Sacramento folks driving around on under-inflated tires. Now, it’s hard to tell when a radial tire is under-inflated. If your manufacturer recommends 35 pounds of pressure, your sedan tire’s considered significantly under inflated at 26 pounds. The tire may not look low until it gets below 20 pounds.
New laws required manufacturers to include a Tire Pressure Monitoring System – or TPMS system – in all cars and light trucks by the 2008 model year. The system has a dashboard mounted warning light that goes off if one or more of the tires falls 25% below manufacturer’s pressure recommendations.
This technology has been used by Sacramento race car drivers for years. They are able to head off problems from under inflation by closely monitoring tire pressure on the track. It’s up to your car’s manufacturer to determine which of many TPMS systems available they’ll use to comply with the law.
Obviously, all of this doesn’t come free for Sacramento drivers. U.S. government studies have estimated the net costs. Of course, the TPMS system itself will cost something. Maintaining the system will have a cost, replacement of worn or broken parts and tire repair cost increases.
The costs are partially offset by savings in fuel and tire wear. There’s also a saving in property damage and travel delay. The net cost is estimated to be between $27 and $100. The government predicts fewer fatal accidents. They estimate that it will cost between three and nine million dollars for every life saved.
Your safety has always been a concern at Made In America / Made In Japan. We want you on the road and accident free. We've traditionally provided things like tire rotations, snow tire mounting and flat fixes at a very low cost. We’ve been able to quickly and cheaply provide the service, and pass the low cost on to you as an expression of our good will.
That’s why we're concerned about how you’ll perceive the changes that this new law will force. Every time a tire is changed: taken off to fix a flat, a new tire installed, a snow tire mounted; the Made In America / Made In Japan service technician is now going to have to deal with the TPMS system.
Even a simple tire rotation will require that the monitor be reprogrammed to the new location of each tire. When a car battery is disconnected, the TPMS system will need to be reprogrammed. TPMS sensor batteries will need to be changed and failed parts replaced.
Like all other Sacramento service centers, here at Made In America / Made In Japan we've had to purchase new scanning equipment to work with the TPMS sensors and to update expensive tire change equipment to better service wheels equipped with the new monitoring systems. Our Made In America / Made In Japan service technicians have been thoroughly trained on many systems and new tire-changing techniques. All of this adds up to significantly increased cost to perform what was once a very inexpensive service for you.
So when you start so see the cost of tire changes, flat repairs and rotations going up at Made In America / Made In Japan, please keep in mind that it’s because of government mandated safety equipment. We want to keep you safely on the road – and we're committed to doing it at a fair price. This new safety equipment will help you avoid the most common types of vehicle failure in Sacramento, and possibly a catastrophic accident.
Posted in the Tires and Wheels category
Power Steering: Keep Headed in the Right Direction, Sacramento
Posted January 19, 2012 1:46 PM
Power steering is standard on nearly every car and truck in Sacramento, California these days. Now there are some exotic, new types of power steering systems, but for the most part, the heart of the system is a pump that’s driven by a belt powered by the engine.
The pump generates boost that assists you as you steer your sedan around Sacramento, California. Power steering systems use hoses to move pressurized fluid back and forth. These hoses can develop leaks so it’s a good idea to inspect them at every oil change.
A check of the power steering fluid level is on the list for every full service oil change because low fluid can damage the power steering pump. And the fluid needs to be compatible with the hoses and seals, so you need to use the correct type –just ask your service consultant at Made In America / Made In Japan.
In addition to providing boost, the fluid cleans, cools and lubricates the power steering system. The lubricants and detergents are depleted over time so you need to replace your old fluid with clean, fresh fluid periodically.
Excess moisture can collect in the power steering fluid as well. That can lead to rust and corrosion as well as reduce the effectiveness of the fluid. Many manufacturers specify power steering service intervals in the owner’s manual. Unfortunately, this important service is sometimes left off the maintenance schedule. When in doubt, every two years is a good fallback.
Your auto service center in Sacramento, California will use a detergent to clean the system, flush out the old fluid and replace it with the good stuff.
Now, if you are experiencing high steering effort, erratic power assist, loud whining coming from the pump you may have a power steering problem. Another sign is that you have to frequently top off the fluid.
Holding the steering wheel to the far right or left for more than a few seconds at a time can wear your pump out real fast. AutoNetTV wants you to be sure to service your power steering system regularly to keep you headed in the right direction.
Fuel System Cleaning At Made In America / Made In Japan
Posted January 11, 2012 12:38 PM
Is your car sometimes hard to start on an early Sacramento morning? When you turn the key, does it hesitate or stutter? If so, the problem could be the result of a dirty fuel system. Your car's fuel system starts with the air filter and ends in the top of your engine. Over time, different parts of the system get dirty, which robs you of performance and hurts your fuel economy.
Most of our sedan in Sacramento have fuel injectors, rather than a carburetor. Fuel injection systems have fewer problems and require less adjustment. But they still need to be properly maintained. This is why your owner's manual has a schedule for cleaning your fuel injectors and other parts of your fuel system.
Some people are interested in buying fuel system cleaners that you can pour into your gas tank. You can do that - and there are lots of great products available that can help maintain an already clean fuel system - but these products cannot do a major cleaning. For that, you need to see your service center at Made In America / Made In Japan. Made In America / Made In Japan has the professional tools and chemicals to really do a complete service.
Your service center at Made In America / Made In Japan in Sacramento California uses a process that gives your car a deep, professional fuel system cleaning. You need to remove particles, gum and varnish from your fuel system and get those injectors running cleanly and efficiently. After a professional fuel system cleaning, you'll notice more power, better fuel economy and reduced exhaust emissions.
The cleaners also help prevent rust and corrosion in your fuel system and lubricate vital engine parts.
Fuel system cleaning is just one of those recommended service items that helps keep your vehicle running strong. As with all maintenance, it can help avoid costly repairs that often result from not taking the right preventive steps. And you will notice the difference in how well your car runs. Check with your service advisor at Made In America / Made In Japan in Sacramento California to see when your car is scheduled for a fuel system cleaning.
An ounce of prevention really is worth a pound of cure.
Posted in the Fuel System category
Wiper Blades In California
Posted January 4, 2012 1:01 PM
If you're gonna drive around the Sacramento area, you've got to be able to see! So having a good pair of windshield wipers is extremely important. We've all experienced the frustration and fear of not being able to see clearly during a storm, or when our windshield is just dirty.
It seems like your wiper blades are always at their worst when you need them the most. But windshield wipers are like most other vehicle parts– they require regular attention in order to work their best.
You really ought to replace your wiper blades twice a year; in the spring and the fall. If it's going to be a particularly harsh winter in Sacramento, you may even want to get special winter blades in the fall. Winter blades are designed to resist freezing.
Speaking of winter and freezing conditions, if your car has been sitting for a long time and the windshield becomes frozen, don't use your wipers to clear off snow and ice. That'll just tear up the blades and cause them to wear out more quickly. It may even damage the wiper motor.
Over time, wiper blades become hard and brittle, and then tear. They also lose their flexibility and just don't cover the windshield effectively.
Worn wiper blades aren't just a safety hazard; they can also scratch your windshield. That may require replacing the entire windshield; a big cost for such a little part.
Replace worn blades right away. Your local service center can provide you with a quality replacement blade. They cost about the same as they would at the store; but installation is included at Made In America / Made In Japan.
Of course you also need washer fluid to help your blades do their work. Even though your local Sacramento service center will top off the washer fluid with a full service oil change, it is a good idea to have some extra fluid at home, or in the car if you are on a long trip.
Always use windshield washer fluid. Plain water, even that fancy bottled water, may freeze in the fluid reservoir or on the windshield itself, making things worse. Besides, water won't do a good job of cleaning your windows.
And remember that some vehicles have two reservoirs: one for the windshield and one for the back window – which may be under the hood or somewhere in the back.
So follow these tips to keep your windshield clear and your eye on the road, and give us a call at Made In America / Made In Japan or come by our shop at 1200 I St, Sacramento, California 95814. Call to make an appointment at 916-442-3287
.
Posted in the Windshield Wipers category
Using Proper Fluids In Your sedan Or Other Vehicle
Posted December 28, 2011 1:38 PM
Today Made In America / Made In Japan is talking about the proper fluids for your vehicle. It's become more complicated with changes in automotive design and manufacturing. It's not that people in California are confused as much as they don't realize how much things have changed in recent years.
If you have questions about the fluids in your vehicle, please don't hesitate to stop by Made In America / Made In Japan. You can find us on 1200 I St in Sacramento, California 95814. Just give us a call at 916-442-3287
Let's take engine oil. Twenty or thirty years ago, there were just a handful of different weights of oil. The weight of an oil is a scientific measure of its properties, particularly its viscosity or thickness.
It was common in those days to use a lighter weight oil in the winter when it's cold outside. That way the oil would be able to splash around inside the engine and protect the parts before it was fully warmed up. And a heavier weight oil would be used in the summer. The thicker oil wouldn't thin out too much in the summer heat and vaporize in the engine.
Modern valve trains have become very complicated with more moving parts and small passages than ever before. The valve train is in the top of the engine, so when the car has been turned off for a while, the oil tends to run down to lower areas and the valve train parts are vulnerable at start-up, before the oil starts circulating.
So new weights of oil have been introduced to meet the engineering specifications of these newer engines.
Manufacturers are recommending specific weights of oil. The recommendation is often printed on the oil fill cap. It's certainly in the owner's manual. Of course, your Sacramento California auto service center can look it up for you.
It's more important than ever to have the correct weight of oil. The wrong weight could actually harm the engine.
Other fluids are also becoming more sophisticated. In the last few years new types of transmission, power brake fluid and coolant have all been introduced for some of the same reasons as for engine oil.
In addition, vehicle manufacturers are now using a wider variety of materials in these systems. Looking at the cooling system as an example, it used to be that the parts were all made out of steel or iron and the hoses were rubber. Now, some parts are plastic, aluminum or other materials.
So the anti-corrosion additives contained in the coolant, or anti-freeze, need to be different in order to protect the different materials used to make the cooling system. If you use the wrong coolant that wasn't formulated to protect your plastic cooling system parts, they could become corroded and fail. And if you're using the wrong coolant, your cooling system won't be covered under warrantee. So it's important to use the right coolant and to not mix different types.
Your owner's manual or your Sacramento California service advisor at Made In America / Made In Japan can make sure you're using the right type. You may have heard of universal coolant. Universal, or global, coolant can be added to other types without harmful reactions. That's OK for an emergency top off, but following your manufacturer's recommendation for your sedan or other auto type is always a safe bet.
In the area of brake fluid, there are a couple of new formulations. It's important to remember that the new ones aren't better than the old ones. They're just different formulations for different vehicles. So if your vehicle calls for DOT 3, using DOT 4 or DOT 5 is not an upgrade. Use the recommended formula.
There are fluid formulations for vehicles with higher mileage. These are special engine oil, transmission fluid, and so on that contain additives to condition and restore seals and gaskets in older engines.
They're fine to use as long as they're a variant of the proper fluid. In other words you can use a high mileage engine oil as long as it's also the correct weight recommended by the manufacturer. Same goes for transmission fluid; as long as it's the right type for your transmission.
Posted in the Fluids category
Emergency Items For Your sedan
Posted December 20, 2011 2:14 PM
Local Sacramento roadside emergencies can range from a flat tire downtown to being stranded in a snowy ravine for three days. So you may want to consider a basic emergency kit to keep in the car at all times and a travel kit tailored to a specific trip.
Your close-to-home kit for around Sacramento would have some basic items to work on your car: everything you need to change a tire, gloves, a couple quarts of oil, some antifreeze and water. A can of tire inflator is a great temporary fix for minor flats. You'll also want jumper cables or a booster box, flares, a flashlight and some basic hand tools.
Now for your comfort and safety: a first aid kit, drinkable water, high calorie food (like energy bars), blankets, toilet paper, cell phone, towel, hat and boots. Keep some change for a pay phone, emergency cash and a credit card.
People who live in areas with frequent severe weather or earthquakes may want to carry provisions for longer emergencies.
For trips away from home, consider the weather and geography as you assemble your emergency supplies. You'll need to have a source of light and heat and will want to provide protection against the elements as well as adequate food and water for everyone in the car.
Always tell people where you are going and have a plan for checking in at waypoints. Then if you run into trouble, you can be reported missing as soon as possible and rescuers will be able to narrow the search area.
The key to safe travel is to keep your vehicle properly maintained, plan ahead, and let others know your itinerary.
Posted in the Parts category
Made In America / Made In Japan On Your Serpentine Belt
Posted December 13, 2011 11:43 AM
Today we’re going to be talking about serpentine belts for our Sacramento California customers. Let’s start by talking about the accessories that are driven by the serpentine belt. First is the alternator. That’s the device that makes electricity to power the vehicle and recharge the battery. Then there’s the air conditioning compressor that makes cool air for you while you're driving around Sacramento California in the summer.
The power steering and power brake pumps are driven by the serpentine belt in most vehicles. Those pumps make the pressure that assists your steering and braking.
In many vehicles, the water pump is driven by the serpentine belt. The water pump is what circulates the coolant that protects your engine. In some cars around Sacramento California, the water pump is driven by the timing belt.
The radiator cooling fans on some vehicles are also driven by the serpentine belt. Some have separate electric motors. That’s really a lot of work for one belt.
But modern engine design has a single belt that snakes around the front of the engine and drives most if not all of these accessories. Serpentine belts do a lot of work, but they’re tough and can last for thousands of miles.
Just how long will they last? That’ll vary for each individual car in the Sacramento California area. Your manufacturer will have a recommendation for when it should be changed, but it could need it sooner. The good news is that a visual inspection can reveal a belt that’s getting close to failing.
Made In America / Made In Japan can look at the belt: if it has more than three or four cracks per inch it needs to be replaced. A deep crack that’s more than half the depth of the belt - replace. Frayed, missing pieces, a shiny glazed look? It’s out of there.
What’s involved in replacing the belt? First the old belt is removed. Then a new one is fitted around all the pulleys for the accessories and the drive. There’s a special pulley called a tensioner.
This pulley is mounted to the engine block with a spring loaded arm. Its job is to apply the correct amount of tension to the belt to keep it from getting loose and maybe slipping off. Because the spring in the tensioner pulley wears out, AutoNetTV recommends replacing them at the same time as the belt. It just makes sense.
What are the warning signs that there’s a problem with the serpentine belt? You may hear a squealing sound from under the hood when accelerating around our Sacramento California streets. A loose belt might give you a slow, slapping sound.
What do you do if your belt breaks? If you’ve actually had that happen on our local Sacramento California freeway, it can be a little scary. Often the first thing you notice is that you have no power steering or power brakes. Don’t panic – you can still steer and brake, but you’ll have to do the work. It’ll be harder to steer and you’ll need more time and effort to stop, so plan accordingly.
Your dashboard will light up will all kinds of warnings. You’ll see a warning about your cooling system if you have a water pump that’s driven by the serpentine belt. This is very critical because without your cooling system working, your engine will overheat. If you don’t stop you’ll have massive engine damage, maybe to the point that you need a new engine. Pull over as quickly as you safely can. Open your windows and turn the heater on full blast to provide a little engine cooling and pulled over as soon as possible.
The battery light will come on because the alternator isn’t working. If your car’s water pump isn’t driven by the serpentine belt, you’re not in danger of overheating so you can drive a little further if necessary. But the battery will run down to the point where the car won’t run and will just shut off. You don’t want that to happen while you’re driving in our local Sacramento California traffic.
Remember, this does not have to happen if you replace your serpentine belt on schedule. Ask your technician at Made In America / Made In Japan to check your belts and hoses from time to time so you can take care of them if they need to be replaced prematurely.